Samsung wf0604nbw xee et
![samsung wf0604nbw xee et samsung wf0604nbw xee et](https://www.delta-elis.com/imgdir/12276-900.jpg)
![samsung wf0604nbw xee et samsung wf0604nbw xee et](https://i.ebayimg.com/images/g/HT8AAOSwRi9d6kbm/s-l960.jpg)
Verify the hot water supply is not set above Turn off the dishwasher and then try to start Water is not making it through the filter. Replace thermistorĬheck for restricted vent Replace ThermistorĬheck wiring to door switch. Power Switch OFF can clear the overload error.Ĭheck for restricted vent. When it happens at more than 800rpm, the process is stopped compulsorily. When the feed back has occcurred twice, Error “8E” is displayed during the dehydrating unbalance sensing, No error happens by overload sensing. If the motor stops working, in one direction ten times, “8E” Error is displayed.ĭuring dehydrating, when the overload is sensed, the motor stops working at once and then feeds back to the initial stage of the dehydration unbalance sensing. However, during the dehydrating stage the signal is to be sensed, when the number of signals reads more than 6 per 500ms during the Washing or Rinsing cycle action. If the fault (low signal) happens to be sensed even once during the washing/rinsing stage, the motor stops immediately. IPM fault signal (this is caused by the overload of the MICOM INTO during motor action). Power 81W OFF can clear the motor restriction error. After ten times, “3E” Error isdisplayed, When the motor Is told to stop because of an operating function. the motor stops working and then returns to the initial stage of the dehydration unbalance sensing cycle. If the motor stops working and this happens in one direction ten times, “3E” Error is displayed.ĭuring dehydrating. If data of hall sensor is less than 2 (2RPM), the Washing motor will stop at once.ĭuring Washing and Rinsing when a motor restriction is sensed, the motor stops and then proceeds to the next water -flow action. This error can be cleared by POWER switch OFF. This error occurs when the Thermistor circuit is abnormal or a voltage of O.2v or below or, 4.5v and over is detected. Water Leakage error occurs when the water drains naturally, (by leakage) after the washing program starts. This error can be cleared by POWER SWITCH OFF. If the water temperature is 50 C or more, during a Delicate or Wool cycle.Īt the time of initial water supply, if the water temperature is not appropriate, the display will show cE. and the display will show 1 E indicating a pressure switch error.Į.g. When this error occurs the drain pump will operate for 3 min. If the same signal is detected for more than 5 seconds, it is a PRESSURE SWITCH Error. * Generated Frequency Signal of WATER LEVEL (WIL) SIW (KHz) The error can be cleared by turning POWER switch OFF. HE, HE1 is displayed if the water temperature rises by 7 C or more in 1 Min or by 2 C or less 20 Min after heating process has started. Unbalance error is cleared by POWER switch OFF and back ON. If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an UE error message will be shown in the display. Laundry load is unbalanced, manually loosen any tangled laundry. The tub is drained for 2 minutes if a frequency of more than 25 KHz is detected. Water is drained prior to POWER switch OFF. It can be cleared by turning POWER switch OFF. Over-Flow error occurs when the water level is too high. The Water Drain error can be cleared by turning POWER SW OFF and back ON. The error status can be cleared by turning the POWER switch OFF and back ON.ĥE is displayed if the water level frequency detected is 25 KHz or less in the initial phase of the UNB -detecting cycle. Water Supply Error occurs when water level frequency does not show changes more than 100Hz or water is not supplied up to the preset water level after 10 Minutes or more at the time of initial water supply.